RP75-481.8S资料

元器件交易网www.cecb2b.comFeatures●Single Output up to 20ADual Outputs Total Current up to 15Aup to 100% Load Imblance●Input/Output 1.6kVDC Isolation●Adjustable Output Voltage, Independently Regulated Outputs●No Minimum Load●Industry Standard Footprint●Halt Tested●Compact 61.0 x 57.91 x 12.7mm Package●HighEfficiency to 90%Selection GuidePart Input Output Output LineLoad Input EfficiencyNumber Voltage Voltage Current Regulation Regulation CurrentSingle Output(VDC) (VDC) (A) (mV) (mV) (A) %RP75-481.8S 36 – 75 1.8 20 4 6 0.915 86RP75-482.5S 36 – 75 2.5 20 5 8 1.255 88RP75-483.3S 36 – 75 3.3 20 7 10 1.618 90RP75-4805S 36 – 75 5 15 10 15 1.838 90RP75-4815S 36 – 75 15 5 30 45 1.860 90Part Input Output Output LineLoad EfficiencyNumber Voltage Voltage Current Regulation Regulation V1 V2 I1 I2Dual Output(VDC) (VDC) (VDC) (A) (A) (mV) (mV) %RP75-483.305DI 36 – 75 5 3.3 15 15 7/10 10/15 88RP75-483.32.5DI 36 – 75 3.3 2.5 15 15 7/5 10/8 81RP75-48051.8DI 36 – 75 5 1.8 15 15 10/4 10/15 85RP75-483.31.8DI 36 – 75 3.3 1.8 15 15 7/4 10/6 81Notes:1.Maximum output deviation is 10% inclusive of remote sense.If remote sense is not being used,the +Vsense should be connected to its corresponding +Vout and likewise the -Vsense should be connectedto its corresponding -Vout..2.Measured with a 1uF M/C and a 10uF M/C(for dual outputs) or 1uF M/C and a 10uF T/C(for single outputs).3.An external filter capacitor is required for normal operation.The capacitor should be capable of handing 1A ripplecurrent for 48V models.RECOM suggest:Nippon chemi-con KMF series,220µF/100V,ESR 90mΩ.4.The negative / positive logic and length are optional ( see table ).The pin voltage is referenced to negative input.5.BELLCORE TR-NWT-000332.Case I:50% Stress,Temperature at Tc=40°C.(Ground fixed and controlled environment)6.Heat sink is optional and P/N:7G-0021,7G-0022,7G-0023,7G-0024.7.The RP75 meets level A and level B conducted emissions only with external components connected before the input pin to the converter.8.Maximum value at nominal input voltage and full load.9.Single:Typical value at nominal input voltage and full load.Dual:The efficiency test condition:Nominal input voltage and both outputs current are 7.5A.10.BASEPLATE GROUNDING:Base-plate should be grounded at one of the four screw bolts prior to operation.11.The converter is provided by basic insulation.12.“NN”for Negative remote ON/OFF.13.“PP”for Positiveremote ON/OFF.144April-2005DC/DC-Converter

INNOLINE

RP75-S_DISeries

75 Watt

IsolatedSingle &

Dual Output

www.recom-international.com

元器件交易网www.cecb2b.comINNOLINEDC/DC-ConverterSpecifications (refer to the standard application circuit,Ta:25°C)Input Voltage RangeUnde-Voltage Lockout Start-up VoltageUnde-Voltage Lockout Shuntdown VoltageInput Filter (Note 3)Input voltage variationInput Surge Voltage 100mS maxStart up timeInput Reflected-Ripple Current(5Hz to 20Hz,12uH Source inpedance)Remote ON/OFF (Note 4)(Positive logic)(Negative logic)Continuous Output PowerOutput Voltage Accuracy (Full load and nominal Vin)Output Voltage AdjustmentSingle (Note 1)DualMinimum LoadLine RegulationLoad RegulationRemote Sense (Note 1)Ripple and Noise 20MHz bandwidth (Note 2) Temperature CoefficientTransient Response Recovery Time (25% load step change)Over Voltage Protection threshold (Non-Latching Hiccup)Over Current Protection thresholdMaximum Total Output CurrentShort Circuit ProtectionEfficiency (at nominal input voltage,full load)Isolation VoltageInput to OutputInput to CaseOutput to CaseI1+ I2DualLL to HL at FL0% to 100% FL36-75VDC 48V input48V inputdv/dt48V inputNominal Vin and constant resistive load48V inputRP75-S_DISeries48V nom.34V typ.32V typ.L-C type5V/ms max(Complies with ETS300 132 part4.4)100VDC25mS typ.20mAp-pON=Open or 3.5V < Vr < 15V,OFF=Short or 0V < Vr < 1.2V,ON=Short or 0V < Vr < 1.2V,OFF=Open or 3.5V < Vr < 15V,IIN=50µA max.IIN=1mA max.IIN=1mA max.IIN=50µA max.75W max.±1.5% +10%,-20%+10%,-10%0%See tableSee table10% of Vout100mVp-p±0.02%/ºC200µs115% ~ 130% of Vout110% ~ 140% of Iout Rated15AHiccup,Automatic recoveryup to 90%.1.600VDC min.1.000VDC min.1.000VDC min.10ohms min.2.500pF max.300KHz typ.-40ºC to +100ºC (base plate)110°C-55°C to +125°C95%MIL-STD-810DContinued next page7Isolation ResistanceIsolation CapacitanceOperating FrequencyOperating Temperature RangeOver Temperature ProtectionStorage Temperature RangeHumidity max.,Non-condensingThermal Shockwww.recom-international.comApril-2005145元器件交易网www.cecb2b.comINNOLINEDC/DC-ConverterRP75-S_DISeriesSpecifications (refer to the standard application circuit,Ta:25°C)Vibration 10 ~ 55Hz 2G,3minutes period,30minutes analogX,Y and ZConducted Emissions EN55022 (Note 7)Level AEN55022 (Note 7)Level BRadiated EmisssionsEN55022Level AESDEN61000-4-2Perf.Criteria2Radiated ImmunityEN61000-4-3Perf.Criteria2Fast TransientEN61000-4-4Perf.Criteria2SurgeEN61000-4-5Perf.Criteria2Conducted ImmunityEN61000-4-6Perf.Criteria2Case Material Open with Aluminium base plateWeightSingle53gDual57gMTBF ( Note 6 )Single2 x106hrs1.3 x106hrsCharacteristicsEfficiency vs Output Load1009080)%70( ycne60iciffE50102030405060708090100Output Power (%) Ta=25°C48V Input Without Heatsink48V Input With Heatsink (7G-0022)110110901.) LFM590901.) LFM590702.) LFM400702.) LFM400))%%(3.) LFM200(3.) LFM200 rreew504.) LFM20w504.) LFM20ooPP ttu30u30ppttuuO10O-40-20123410020406080100-40-201234020406080100Ambient Temperature (°C)Ambient Temperature (°C)146April-2005www.recom-international.com元器件交易网www.cecb2b.comINNOLINEDC/DC-ConverterPackage Style and Pinning (mm)RP75-S_DISeries3rd angleprojectionSingle Output57.9160.9612.705.0848.26Side View50.804xM3 x 0.5 ( Note 10)Pin ConnectionsPin #Function1–Vin2Case3 Remote ON/OFF4+Vin5–Vout6 –Vsense7Trim8+Vsense9+VoutXX.X± 0.5 mmXX.XX± 0.25 mmPin pitch tolerance 0.35mmPin Ø1.016 mm1.016 mm1.016 mm1.016 mm2.032 mm1.016 mm1.016 mm1.016 mm2.032 mm1235.5615.24345678917.7810.1625.40Bottom ViewExternal Output TrimmingOutput can be externally trimmed by using the methodshown below.See application notes for values.Product Options TableOptionNegative remote ON/OFF logic,0.20”pin length (standard)Negative remote ON/OFF logic,0.145”pin lengthNegative remote ON/OFF logic,0.11”pin lengthLKPSMSuffix7Trim UpRU6Trim DownRDPositive remote ON/OFF logic,0.20”pin lengthPositive remote ON/OFF logic,0.145”pin lengthPositive remote ON/OFF logic,0.11”pin length87Example: RP75-483.3S/Pwww.recom-international.comApril-2005147元器件交易网www.cecb2b.comINNOLINEDC/DC-ConverterRP75-S_DISeriesPackage Style and Pinning (mm)Dual Output3rd angleprojection57.9160.965.0812.70Side View48.2650.804xM3 x 0.5 ( Note 10)Pin ConnectionsPin # FunctionPin Ø1.016 mm151–Vin2Case1.016 mm3 Remote ON/OFF1.016 mm35.5664+Vin1.016 mm2Bottom View5+V21.016 mm725.406 –V2 (Com)1.016 mm15.2410.1640.647V2 Trim1.016 mm8+V11.016 mm9 +V1 (Com)1.016 mm3810V1 Trim1.016 mm9XX.X± 0.5 mmXX.XX± 0.25 mm4Pin pitch tolerance 0.35mm10External Output TrimmingProduct Options TableOutput can be externally trimmed by using the methodOptionSuffixshown below.See application notes for values.Negative remote ON/OFF logic,0.20”pin length (standard)( ) for V2 output trimNegative remote ON/OFF logic,0.145”pin lengthL9(6)Trim Up10(7)Trim DownNegative remote ON/OFF logic,0.11”pin lengthKPositive remote ON/OFF logic,0.20”pin lengthPRURDPositive remote ON/OFF logic,0.145”pin lengthS10(7)8(5)Positive remote ON/OFF logic,0.11”pin lengthMExample: RP75-483.305I/N148April-2005www.recom-international.com